SEnukeX SEO Software

Sunday, January 16, 2011

History of Fiber Optics Technology







In 1880 Alexander Graham Bell invented a light communications system called photo-phone using sunlight reflected from a voice-modulated thin mirror to bring the conversation. Photo-phone never achieved commercial success, although the system is working quite well. Here are some of the stages of historical development of optical fiber technology:



1.       First generation Instance (starting 1970)
System is still simple and the basis for the next generation system consists of:
Encoding: Changing input (eg voice) into electrical signals.Transmitter: Changing the electrical signals into modulated light wave, a LED with a wavelength of 0.87 μm. Silica Fibers: As an introduction to waves of light.Repeater: For a light wave amplifier which weakened on the road
Receiver: Change the modulated light waves into electrical signals, a photo-detector
Decoding: Changing the electrical signals into output (eg voice). Repeater works by converting light waves into electrical signals and then amplified electronically and converted back into light waves. In 1978 the transmission capacity can reach 10 Gb.km / s.

2.       Second generation (beginning in 1981)
To reduce the effect of dispersion, fiber core size minimized. The refractive index of the skin was made in close with the core refractive index. Using a laser diode, the emitted wavelength 1.3 μm. Transmission capacity to 100 Gb.km / s.

3.        Third generation (starting 1982)
Completion of the manufacture of silica fibers. Making a laser diode chip wavelength 1.55 μm.
Improved purity silica material so that transparency can be made for a wavelength of about 1.2 μm to 1.6 μm  Transmission capacity into several hundred Gb.km / s

4.        Fourth geneartion (starting 1984)
Commencement of research and development of a coherent system, rather than modulating the intensity modulation, but frequency modulation. In 1984 its capacity has been able to equal the capacity of a direct detection system (intensity modulation). Hampered its development because of technological tools and the source of the frequency modulation detection is still far behind.

5.       Fifth generation (beginning in 1989)
Developed an optical amplifier repeater function which replaces the previous generations.
In the early development of transmission capacity is only achieved 400 Gb.km / s but a year later the transmission capacity has penetrated 50,000 Gb.km / s!

6.       Top-Six generation?
In 1988 Linn F. Mollenauer pioneered optical soliton communication systems. Soliton is a pulse wave that consists of many components of different wavelengths and also varies only slightly in intensity. Soliton length is only 10 -12 seconds and can be divided into several components that are close together, so that the signals in the form of solitons is information that consists of multiple channels at once (wavelength division multiplexing). We experimentally demonstrated that solitons can carry a minimum of 5 channels, each of which carries information at a rate of 5 Gb / s. Transmission capacity has been tested 35,000 Gb.km / s. The workings of this system is the effect of Kerr solitons, ie the rays will travel the same wavelength at different rates within a material when its intensity exceeds a limit price. This effect is then used to neutralize the effects of dispersion, so that the soliton does not widen at a time until the receiver. This is very advantageous because the resulting error rate is very small and even negligible.



Although the light propagates along the fiber core without the layer of leather material, but the skin has several functions:
- Reduce the loss of light from the core to the surrounding air.
- Reduce the scattering loss at the core surface.
- Protects the fiber from contamination of surface absorption.
- Increasing the mechanical strength.
If the difference in the refractive index of the core and made drastic skin called the optical fiber Step index (SI), the difference between skin and core refractive index is symbolized by Δ, where:


For additional protection, leather wrapped by an additional layer (made of certain types of plastic) which is a coat or a buffer to protect the optical fiber from physical damage.Buffer is elastic, prevent abrasion and prevent loss due to scattering microbends.

2.flow of Fiber Optic Light Inside

The concept of propagation of light in optical fibers, can be reviewed by two approaches / theories of geometric optics in which light rays are seen as fulfilling the laws of geometric light (reflection and refraction) and physical optics in which light is seen as an electro-magnetic waves (mode theory) . Overview of Geometric Optics  Gives a clear picture of the propagation of light along optical fibers. Two types of rays can propagate along optical fibers where the light rays propagate meridian cuts the optical fiber axis and the skew ray in which the rays do not propagate through the fiber optic axis. Meridian-ray beam can be classified into bound and unbound rays. Bound rays in optical fiber due to total reflection, in which order these events occur then the beam entering the fiber core must be cut border skin with a greater angle than the critical angle, the EC, so that light can propagate along the fiber.


Overview of physical optics Approach as a ray of light just to explain how the direction of a plane wave propagating in a fiber but does not review other properties of plane waves of interference, in which the plane waves interfere with each other along the propagation, so that only the types of certain plane waves which can propagate along the fiber . It would require a review of physical optics is looking at light as an electromagnetic wave is called the theory of modes. The theory used to explain the mode in addition to the types of plane waves which can propagate along the fiber, also for explaining the properties of optical fibers such as absorption, attenuation and dispersion. Mode is a "configuration of light propagation in optical fibers that provide the transverse electric field distribution in a stable (unchanged throughout the propagation of light in the direction of the axis) so that light can be guided in the fiber optics" (Introduction To Optical Fiber Communication, Yasuharu Suematsu, Ken - Ichi Iga). Collection of electromagnetic waves guided in the optical fiber are called modes. View mode theory of light as a plane wave which is expressed in the direction, amplitude and wavelength of perambatannya. Plane wave is a wave surface (which on the surface of this phase of his constant, called a wavefront) is an infinite flat plane perpendicular to the direction of propagation. Relationships wavelength, propagation speed and wave frequency in a medium. Why is fiber optic system is said to revolutionize the world telekomunikiasi? is because compared with the conventional system using metal wires (copper) used, the optical fiber having: Less expensive - Several miles of optical cable can be made cheaper than copper wires of equal length. Thinner - Optical fibers can be made with smaller diameter (the size of the skin of the fiber diameter about 100 μm and total diameter coupled with a protective jacket around 1-2 mm) than copper wires, and also because the optical fiber carrying light (light) then it certainly has a light weight (reduced weight). So fiber-optic cables take a smaller place in the soil. Higher carrying capacity - Because optical fibers are thinner than copper wires then most of the optical fiber can be bundled into a cable with a certain diameter of the multiple telephone lines may be on the same cable or more channels on cable TV can be through cable. Fiber optics also has a large bandwidth (1 and 100 GHz, for multimode and single-mode along the 1 km). Less signal degradation - The signal loss in optical fibers is smaller (less than 1 dB / km at a wide range of wavelengths) as compared with copper wire.Message Origin Message origin can be a non-electric physical quantities (sound or picture), so that the necessary transducers (sensors) that alter message from form to form a non-electric power. A common example is a microphone to change sound waves into electrical currents and video cameras (CCD) transforms the image into electrical current.Modulator and Carrier Source Have two main functions, the first electrically changing message into a form suitable, both laid it on the signal generated by carrier wave source. Modulation formats can be differentiated into analog and digital modulation. In digital modulation for laying the digital data signal on a carrier wave, the modulator simply just to on his or her right off the carrier signal source according to his data. Carrier sourc membangkitkankan light waves, which are commonly used Laser Diode (LD) or Light Emitting Diode (LED).Channel Coupler To channel the power of light waves that have been modulated from the carrier source to the information channel (fiber optics). Is an important part of the design of optical fiber communication systems because the possibility of loss is high.Information Channel (Fibre Optics) Desirable characteristics of optical fibers is attenuation and low-angle light-cone of acceptance. Amplifier connections required at the very long (hundreds or thousands of kilometers) in order to have sufficient power to the receiver. Repeaters can be used only for the digital system, which serves to change the weak optical signal into electrical form and then strengthened and restored to form an optical signal for subsequent transmission. Time propagation of light in an optical fiber depends on the frequency of light and the path through which, the signal light propagating in optical fibers have the different frequencies within a certain range (the width of the frequency spectrum) and powernya divided over different paths, different, this causes a distortion in the signal. In digital systems this distortion in the form of widening (dispersion) of digital pulses that propagate in the fiber optics, is increasingly widening with increasing distance traveled and the widening of this will overlap with other pulses, it will cause errors in signal detection. The existence of dispersion limit the speed of information (on speed digital information system called the data rate measured in bits per second (bps)) that can be delivered. On the phenomenon of optical solitons, dispersion effect is balanced by nonlinear effects of optical fibers so that the pulse signal can propagate without changing shape (not dilated).Detector and Amplifier Used photo-detectors (photo-diode, photo transistor, etc.) that serves to change the received optical signals into electrical signals.Signal Processor For analog transmission, the signal processor consists of strengthening and signal filtering. Filtering aims to maximize the ratio of signal power to signal power that is not diinginakan. Random fluctuations that exist in the received signal is referred to as noise. How does this noise on the communication system is determined by the amount of SNR (Signal to Noise Ratio), the ratio of signal power to noise power, usually expressed in desi-Bell (dB), the greater the SNR the better the quality of the communication system to noise. For digital systems, signal processor consists of strengthening and filtering the signal and sets of decision makers. The series of these decision makers to decide whether a binary 0 or 1 is received during the time slot of each individual bit. Because of the noise that can not be eliminated then there is always the possibility of errors of this decision-making process, expressed in magnitude Bit Error Rate (BER) that its value should be small in communication. If the data is transmitted is an analog (eg voice), but is transmitted digitally over fiber optics (the transmitter is required Analog to Digital Converter (ADC) before incoming signal modulator) is also required Digital to Analog Converter (DAC) to signal processor, to transform digital data into analog, prior to release to the output (eg speaker).Message Output If the resulting output are presented directly to the people, who hear or see such information, then the output is still in the form of electrical signals to be converted into sound waves or visual image. Transducer (actuator) for this are the speakers for the audio message and a cathode ray tube (CRT) (or others such as LCD, OLED, etc.) for the visual image. In some situations such as in systems in which computers or other machines connected together via a fiber optic system, then the output in the form of electrical signals can directly be used. This is also when the optical fiber system is only part of a larger network, as in a fiber link between the telephone exchange or a fiber trunk line carrying a number of television programs, in this case includes the distribution of processing electrical signals to certain goals desired. Equipment at the ouput message is simple only in the form of an electrical connector to the signal processor the next system.

No comments: